Do It Yourself Bathtub Installation.
Do It Yourself Bathtub Installation.
Blog Article
What're your opinions about A Step-by-Step Guide to Installing a Bathtub?
Mounting a bath tub isn't specifically brain surgery, however it does need solid plumbing, carpentry, as well as in some cases, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably tough job. If the old tub is easily available, the project can relocate easily; if you need to open up a wall surface to eliminate the old tub and place the brand-new tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will need an assistant to vacate the old bathtub as well as set in the brand-new one. See to it you have qualified on your own for the work as well as are comfortable attempting it. As opposed to employing a specialist to take over a halfway-completed project, it is far better to think about employing one before you start. Possibilities are you may require an expert plumber to make tube links.
This post will aid you install a brand-new tub in your bathroom if you have currently purchased a brand-new bathtub and do not need to alter the arrangement of your previous water system pipes.
Your devices and product checklist must comprise the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water supply. After doing so, switch on the taps to drain any kind of water remaining in the system. The procedure of removing the existing taps can be fairly problematic because of the limited gain access to that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly originate from the pipes. When the supply pipelines have been eliminated, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing compound.
Before proceeding to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin guaranteeing that the washers remain in location in between the faucet and also the sink. Safeguard the faucet in position with the maker supplied backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind must be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Mounting the Bath tub
Making use of both wood boards under its feet, put the tub in the needed setting. The wooden boards are useful in evenly spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The next goal is to ensure that the bath tub is leveled all round. This can be attained by examining the level as well as adjusting the feet on the bathtub till the level checks out level.
To install faucets, fit all-time low of the outermost versatile tap adapter to the ideal supply pipeline by making a compression join; then do the very same for the various other tap.
Switch on the water and also inspect all joints and new pipework for leakages as well as tighten them if necessary. Fill the bath tub and also examine the overflow electrical outlet as well as the normal electrical outlet for leaks.
Finally, deal with the bathroom paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the bath tub ought to wait until the bath tub has been made use of a minimum of when as this will settle it right into its final placement.
Getting ready for the Installation
To start with, the supporting frame provided with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets system to stop stress on the tub.
Fit the flexible faucet connectors to the bottom of the two faucets utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final placement.
Tiling Around the Bathtub
In the area where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture a rigid seal, triggering the water to pass through the wall surface between the bath as well as the tiling, bring about complications with dampness as well as feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and also fittings. They are sold in tubes as well as cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of soaked newspaper or soft rope. Remember to always fill up the tub with water prior to securing, to permit the activity experienced when the bathtub remains in use. The sealer can fracture rather very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly offered on the marketplace. It is a good idea to fit the ceramic tiles utilizing waterproof or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our excerpt on Tools You Need to Install a New Bathtub . Thanks a lot for spending some time to read our posting. Loved our write up? Please share it. Let someone else find it. Many thanks for your time. Don't hesitate to pay a visit to our website back soon.
Get Quote Report this page